Page 1 of 2

Skinning a coyote the right way!

Posted: Thu Sep 04, 2008 4:15 pm
by hunter1187
Hey guys, I want to skin (de-fur) my own coyotes this year. Any tips or really pics will be good on the cuts I need to make. I know it has to be done right. Any info will be Great!!

Re: Skinning a coyote the right way!

Posted: Thu Sep 04, 2008 4:48 pm
by Dcoy
Hunter,
Hi,I'll have to 'de-fur'to the experts on this one.Geez,sorry,just couldn't resist. :D
I'll get a grip.Good hunting!

Re: Skinning a coyote the right way!

Posted: Fri Sep 05, 2008 3:46 am
by Coyotehunter
A great video to pick up is Blaine Eddys "Skinning for Profit"

Re: Skinning a coyote the right way!

Posted: Fri Sep 05, 2008 4:18 am
by lyonch
I have recently purchased Tom Osbornes "Practical Fur Handling" video and he is very in depth on what he does. Here is the link to the movie: http://www.fntpost.com/Products/Fur+Han ... ideo+(DVD)

The movie by Blaine Eddy "Skinning for Profit" is also a great movie. The only advice i can give you is get a video, and watch it a few times before you plan on skinning. If you are experienced with skinning animals it might only take you one watch and you will understand. Hope this helps. Another hint that i have heard from jamie several times is "get them while there hot" there is a lot of truth to that!!!!

Re: Skinning a coyote the right way!

Posted: Fri Sep 05, 2008 5:18 am
by LeviM
I perfer to take my coyotes back home and skin them. I would rather be heading to my next spot then skinning a coyote in the field. It is way easier to skin them while their hot. I perfer to take advantage of every minute of a good day of calling, plus if I take them home I can enjoy a nice "cold one" while skinning.

Re: Skinning a coyote the right way!

Posted: Wed Sep 10, 2008 11:27 am
by Prairie Ghost
I'm planning on a doing a video on it in the top dog forum but blaines video is a good one

Re: Skinning a coyote the right way!

Posted: Mon Dec 15, 2008 8:29 pm
by EO caller
Any tips on skinning in the field as far as skinning without a gamble? Is there any super fancy tricks to make it easier. :?

Re: Skinning a coyote the right way!

Posted: Tue Dec 16, 2008 5:29 am
by Daryl
Rope and a fence post :D

Re: Skinning a coyote the right way!

Posted: Tue Dec 16, 2008 2:52 pm
by Coyotehunter
yep that will work. I do like having a stout stick or something for the shoulders. I use a 1/2 " rod that has a rounded tip at home.

Re: Skinning a coyote the right way!

Posted: Tue Dec 16, 2008 4:15 pm
by Daryl
I will give you a tip on a shoulder plunger! I have a pushrod out of a N14 Cummins engine and it works perfect. If any of you have a local truck shop go ask them if they have a old one laying around you won't be disapointed. Very hard steel and a rounded tip.

Re: Skinning a coyote the right way!

Posted: Tue Dec 16, 2008 5:23 pm
by lyonch
For a shoulder plunger i use a old very smooth steel that is used to sharpen knifes. It has a blunt end on it and works great. I would prefer something with a smooth finish on it to allow the hide to slide on it as you pull. Just my 2 cents.

Re: Skinning a coyote the right way!

Posted: Tue Dec 16, 2008 6:03 pm
by EO caller
Thanx guys. That should speed me up a little. My dad taught me the shoulder trick, but he uses a ballpeen hammer to punch a hole so you can get a couple of fingers in there, But being a trucker I like the push rod deal. We will try it.

Re: Skinning a coyote the right way!

Posted: Tue Dec 16, 2008 6:03 pm
by LeviM
I just use 1/2" rebar or most of the time a knife sharper like chris mentioned

Re: Skinning a coyote the right way!

Posted: Tue Dec 16, 2008 6:13 pm
by Daryl
Levi run out to Cummins and ask them for a couple old pushrods from a N14. You will like it I promise :wink:

Re: Skinning a coyote the right way!

Posted: Wed Dec 17, 2008 10:12 am
by Fallguy
For a shoulder tool I just went and found an old motor shaft in my dads shop. I cut it to a length of about a foot and a half. I suppose it is 1/2 in diameter and heavy. Probably overkill but I use it for other stuff in the garage like unplugging the snowblower and leverage on wrenches. It a cheap useful tool.