Page 2 of 2

Re: Removing Moly Coating

Posted: Sat Feb 14, 2009 5:01 pm
by LeviM
xdeano wrote:Well, I guess they don't make the product any longer. Sorry man. It was a good product.
xdeano
Thanks for the info though

Re: Removing Moly Coating

Posted: Sun Mar 01, 2009 11:01 am
by xdeano
i forgot to mention JB bore paste. That works pretty decent too.

xdeano

Re: Removing Moly Coating

Posted: Mon Apr 06, 2009 6:40 am
by LeviM
I first want to thank everyone for their tips!!! I went with Jeff's advice and tried some Witches Brew! That stuff is nasty. It did a really good job, it pretty much boiled that crap out. I warn anyone, removing moly is a messy, messy, messy job! :x I plan on buying a cheap box of bullets firing them through and going back through with some more witches brew to make sure its all out before testing any of my reloads. Thank again guys!!

Side Note: Witches Brew, sounds like the crap I drank in college!!! :)

Re: Removing Moly Coating

Posted: Mon Apr 06, 2009 6:49 am
by Dcoy
Orange vodka and milk works also if you're talking young and foolish. :D

Re: Removing Moly Coating

Posted: Mon Apr 06, 2009 6:53 am
by LeviM
LMFAO :lol:

That sounds kind of good though, and thats pretty much what witches brew looks like!!!!

Re: Removing Moly Coating

Posted: Mon Apr 06, 2009 12:53 pm
by Prairie Ghost
Dcoy i thought it was all "moonshine" in your days LOLOL :shock:

Re: Removing Moly Coating

Posted: Mon Apr 06, 2009 2:45 pm
by Dcoy
Yeh a little of that around.The meth of my era though was 'Everclear'.Anyone remember that stuff?Fill half a 7-Up bottle with that and go nuts for 24 hours. :D Had to be careful with matches around it.
Got a buddy that still thinks its the stuff that powered man to the moon.Of course he thinks he's there most of the time anyway.

Re: Removing Moly Coating

Posted: Mon Apr 06, 2009 6:46 pm
by Prairie Ghost
that stuff should be banned............No SERIOUSLY that stuff should be banned thats just trouble in a bottle

Re: Removing Moly Coating

Posted: Sat Apr 18, 2009 5:23 pm
by Coyotehunter
"GM Top Engine" cleaner and a new brush.

Re: Removing Moly Coating

Posted: Wed Apr 22, 2009 7:44 pm
by jaybic
For removing moly, I have had best luck with Sweets 7.62 and if needed JB borepaste/bore bright. Just dont go sniffing the Sweets bottle and be sure to use a nylon brush. You put Sweets on a .22 cal copper/brass brush and it'll be a .17 cal brush by the time your done cleaning. NOT KIDDING!

Dcoy, you can still buy Everclear down here in MN. I dont know if it removes copper from a rifle barrel but it does a great job of removing any intelligence you might have, function to your liver, motor skills, judgement and does equally well removing stomach contents towards the end of an evening and best of all, only takes about 3 shots to do it.

Those of you who have tried know what I mean.

Jaybic

Re: Removing Moly Coating

Posted: Thu Apr 23, 2009 3:45 am
by Dcoy
Jaybic,
Didn't know the 'stuff' was still around.Scary.Explains a lot-the way a few buddies from there act,Mn politics,etc.I know my early use undoubtedly contributed to my ongoing state of confusion.
As to using it on Moly,I don't know either but I'd be more afraid for the barrel itself. :D